What is the maximum operating pressure for the Walterscheidâ¢ WE-BT angle screw connection, carbon steel, per DIN 2353 with a 2.5:1 safety factor?

The maximum operating pressure for the Walterscheidâ¢ WE-BT angle screw connection, carbon steel, per DIN 2353 with a 2.5:1 safety factor depends on the connector series (LL, L, S) and the nominal size (thread/outer diameter). DIN 2353 specifies maximum working pressures for tube fittings based on material and wall thickness; with carbon steel fittings and a 2.5:1 safety factor typical allowable working pressures are approximately: - Very light series (LL): up to ~250 bar (depending on size) - Light series (L): up to ~350â420 bar (depending on size) - Heavy series (S): up to ~420â630 bar (depending on size) To determine the exact maximum operating pressure for a specific Walterscheidâ¢ WE-BT angle screw connection, carbon steel (given thread size and series), consult the Eaton/Walterscheid product data sheet or DIN 2353 tables for the precise nominal size.these provide the certified maximum working pressure values per series and size with the 2.5:1 safety factor.

How do I select the correct size of Walterscheidâ¢ WE-BT angle screw connection, carbon steel, for LL, L, and S series per DIN 2353?

To select the correct Walterscheidâ¢ WE-BT angle screw connection, carbon steel for LL, L, and S series per DIN 2353, follow these steps: 1. Determine system working pressure and peak loads. 2. Choose series by required strength: LL for very light-duty, L for light-duty, S for heavy-duty. S series used where higher burst/working margins and mechanical robustness are needed. 3. Verify thread and seat compatibility: Walterscheidâ¢ WE-BT uses a 24Â° DIN 2353 socket with external metric thread and external BSPT thread; sealing is on the thread (use PTFE tape or anaerobic sealant). 4. Confirm component dimensions and thread size per DIN 2353 tables for the chosen series to match hose fitting and port. 5. Ensure safety factor 2.5:1 is acceptable for your application and that material (carbon steel with Guardian Sealâ¢ galvanic coating) meets corrosion and environmental requirements. 6. If in doubt, consult DIN 2353 dimension/pressure charts or supplier for exact size selection and compatibility.

Can Walterscheidâ¢ WE-BT angle screw connection, carbon steel, be used with PTFE tape or anaerobic sealant on BSPT threads per DIN 2353?

Yes. Walterscheidâ¢ WE-BT angle screw connection, carbon steel can be used with PTFE (Teflon) tape or anaerobic sealant on the BSPT (British Standard Pipe Taper) external thread per DIN 2353. The product description explicitly states that the BSPT thread seals on the thread and may be sealed using Teflon tape or anaerobic sealant. Key points to follow: - Use PTFE tape or an appropriate anaerobic thread sealant compatible with carbon steel and hydraulic fluids in your system. - Apply sealant/tape to the BSPT taper thread only; avoid contaminating the internal 24Â° DIN 2353 sealing cone and sealing surfaces (the cone must remain clean and undamaged for metal-to-metal sealing). - Assemble and torque to Eaton/Walterscheid recommended values for the specific WE-BT series (LL, L, S) and thread size to ensure correct sealing and the rated safety factor (2.5:1). - Confirm chemical compatibility of the chosen sealant with system fluid and operating temperature; follow manufacturer curing/installation instructions for anaerobic sealants. - Inspect for leaks after assembly and pressure test per relevant procedures. Following these precautions ensures proper sealing of the BSPT thread while preserving the DIN 2353 24Â° cone sealing function.

Raccord coudé vissé Walterscheid™ WE-BT, acier au carbone

Informations complémentaires

Matériau	CS – acier (fonte)

Raccord coudé à visser DIN 2353 Eaton Walterscheid™ type WE-BT : douille 24° DIN 2353 avec filetage métrique extérieur et filetage BSPT extérieur (étanchéité sur le filetage – avec ruban Téflon ou produit anaérobie). Coefficient de sécurité 2,5:1. Disponible en : LL (série très légère), L (série légère), S (série lourde). Matière : acier au carbone avec revêtement galvanique Guardian Seal™.

Liste des variantes de produit

Référence article	Nom de la variante du produit	DN	BAR	Disponibilité	Actions
HD-WE-04LL-BT-02-W	raccord Walterscheid DIN 2353 WE 4LL 1/8" BSPT	-	100	En stock	Demande
HD-WE-06L-BT-02-W	Raccord Walterscheid DIN 2353 WE 6L 1/8" BSPT	-	250	En stock	Demande
HD-WE-06L-BT-04-W	Raccord Walterscheid DIN 2353 WE 6L 1/4" BSPT	-	250	En stock	Demande
HD-WE-06LL-BT-02-W	Raccord Walterscheid DIN 2353 WE 6LL 1/8" BSPT	-	100	En stock	Demande
HD-WE-06S-BT-04-W	Raccord Walterscheid DIN 2353 WE 6S 1/4" BSPT	-	630	En stock	Demande
HD-WE-08L-BT-04-W	Raccord Walterscheid DIN 2353 WE 8L 1/4" BSPT	-	250	En stock	Demande
HD-WE-08LL-BT-02-W	raccord Walterscheid DIN 2353 WE 8LL 1/8" BSPT	-	100	En stock	Demande
HD-WE-08S-BT-04-W	Raccord Walterscheid DIN 2353 WE 8S 1/4" BSPT	-	630	En stock	Demande
HD-WE-10L-BT-04-W	Raccord Walterscheid DIN 2353 WE 10L 1/4" BSPT	-	250	En stock	Demande
HD-WE-10L-BT-06-W	Raccord Walterscheid DIN 2353 WE 10L 3/8" BSPT	-	250	En stock	Demande
HD-WE-10S-BT-06-W	Raccord Walterscheid DIN 2353 WE 10S 3/8" BSPT	-	630	En stock	Demande
HD-WE-12L-BT-04-W	Raccord Walterscheid DIN 2353 WE 12L 1/4" BSPT	-	250	En stock	Demande
HD-WE-12L-BT-06-W	Raccord Walterscheid DIN 2353 WE 12L 3/8" BSPT	-	250	En stock	Demande
HD-WE-12S-BT-06-W	Raccord Walterscheid DIN 2353 WE 12S 3/8" BSPT	-	630	En stock	Demande
HD-WE-15L-BT-08-W	Raccord Walterscheid DIN 2353 WE 15L 1/2" BSPT	-	250	En stock	Demande
HD-WE-16S-BT-08-W	Raccord Walterscheid DIN 2353 WE 16S 1/2" BSPT	-	400	En stock	Demande
HD-WE-18L-BT-08-W	Raccord Walterscheid DIN 2353 WE 18L 1/2" BSPT	-	160	En stock	Demande

Vous avez besoin d'une plus grande quantité de produits ou d'un devis personnalisé ?

Appelez-nous : +33 679 352 568 ou envoyez-nous un e-mail : wirthjeanpierre@aol.fr

Envoyer une demande

Raccord coudé à visser DIN 2353 Eaton Walterscheid™ type WE-BT : douille 24° DIN 2353 avec filetage métrique extérieur et filetage BSPT extérieur (étanchéité sur le filetage – avec ruban Téflon ou produit anaérobie). Coefficient de sécurité 2,5:1. Disponible en : LL (série très légère), L (série légère), S (série lourde). Matière : acier au carbone avec revêtement galvanique Guardian Seal™.