Is the Thermoplastic double hose with aramid braid F2220 compatible with hydraulic oil, gases, air, fuels and water-based fluids across its full temperature and pressure range?

Thermoplastic double hose with aramid braid F2220 is designed for hydraulic oil installations, gases, air, fuels and water-based fluids and.within the limits specified.is compatible with those media. Its construction: polyester inner tube, double aramid braid reinforcement and microâperforated polyurethane outer layer meets standards SAE 100R8 / ISO 3949âR8. Working pressure ranges from 250 to 362 bar depending on diameter. Operating temperature range is â40Â°C to +93Â°C generally; for water and air the upper limit is +65Â°C. Important: compatibility depends on specific fluid formulations, concentrations and full operating conditions (pressure, temperature, additives). For critical applications confirm chemical compatibility and safety margins with the hose manufacturer or provide fluid details for verification.

Does Thermoplastic double hose with aramid braid F2220 require special fittings for high-pressure hydraulic oil and gas applications?

Thermoplastic double hose with aramid braid F2220 does not inherently require special fittings beyond those appropriate for highâpressure hydraulic and gas service. Because itâs rated to 250â362 bar and uses aramid braid reinforcement with thermoplastic inner/outer layers, use fittings that: - are rated for the hoseâs maximum working pressure and matched to the specific hose diameter, - are compatible with thermoplastic/polyurethane materials (to avoid chemical or abrasion issues), - provide secure crimping or mechanical attachment suitable for doubleâhose constructions or welded outer layers, - meet relevant standards for hydraulic/gas systems and sealing (e.g., SAE/ISO as applicable). For gas applications and critical highâpressure systems, consult the hose manufacturerâs recommended fittings and assembly procedure to ensure safety, correct swaging/crimp profiles, and compliance with regulations.

Can Thermoplastic double hose with aramid braid F2220 be used for potable water or only non-potable water-based fluids?

Thermoplastic double hose with aramid braid F2220 is designed for hydraulic oil, gases, air, fuels and water-based fluids, but the provided description does not explicitly state suitability for potable (drinking) water. Key points affecting potable use: - Materials: inner layer is polyester and reinforcement is aramid braid. Polyester is not typically certified food-contact by default; aramid fibers are not intended as food-contact materials and could present contamination risks if not encapsulated or specifically certified. - Outer layer: micro-perforated polyurethane. perforation suggests possible exchange with environment and is not compatible with potable-water hygiene requirements. - Standards listed (SAE 100R8, ISO 3949-R8) are hydraulic hose standards, not potable water or drinking-water approvals (e.g., NSF/ANSI 61, WRAS, KTW). - Temperature note: âfor water and air up to +65Â°Câ addresses performance but not sanitary safety. Conclusion: Thermoplastic double hose with aramid braid F2220 should be considered suitable only for non-potable water-based fluids unless the manufacturer provides explicit potable-water certifications (NSF/ANSI, WRAS, KTW or equivalent) and documentation that all materials and construction meet drinking-water safety. Request manufacturer certification if potable use is required.

Tuyau thermoplastique double à tresse aramide F2220

Flexibles thermoplastiques, Tous les produits/

Informations complémentaires

Matériau	PEE – polyester
Température maximale de service [°C]	93
Température de service minimale [°C]	-40
Résistance au vide	vérifier

Tuyau léger et souple en version double (deux tuyaux dont le revêtement est soudé) destiné aux installations hydrauliques à huile, aux gaz, à l’air, aux carburants et aux fluides à base d’eau. Normes : SAE 100R8, ISO 3949-R8. Âme : polyester. Renforcement : double tresse aramide. Revêtement : polyuréthane microperforé. Pression de service : de 250 bar à 362 bar, selon le diamètre du tuyau. Température de service : de -40°C à +93°C (pour l’eau et l’air jusqu’à +65°C).

Liste des variantes de produit

Référence article	Nom de la variante du produit	DN	BAR	Disponibilité	Actions
MC-F2220C-06	Tuyau thermoplastique F2220C 2x1/4"	6	362	En stock	Demande
MC-F2220D-08	Tuyau thermoplastique F2220D 2x5/16"""	8	350	En stock	Demande
MC-F2220E-10	Tuyau thermoplastique F2220E 2x3/8"	10	300	En stock	Demande
MC-F2220F-13	Tuyau thermoplastique F2220F 2x1/2"	12	250	En stock	Demande

Vous avez besoin d'une plus grande quantité de produits ou d'un devis personnalisé ?

Appelez-nous : +33 679 352 568 ou envoyez-nous un e-mail : wirthjeanpierre@aol.fr

Envoyer une demande

Tuyau léger et souple en version double (deux tuyaux dont le revêtement est soudé) destiné aux installations hydrauliques à huile, aux gaz, à l’air, aux carburants et aux fluides à base d’eau. Normes : SAE 100R8, ISO 3949-R8. Âme : polyester. Renforcement : double tresse aramide. Revêtement : polyuréthane microperforé. Pression de service : de 250 bar à 362 bar, selon le diamètre du tuyau. Température de service : de -40°C à +93°C (pour l’eau et l’air jusqu’à +65°C).