Is AS7 CONDUCTIVE double braided polyester thermoplastic hose safe for use with isocyanates and solvent-based paints at -40Â°C to +100Â°C?

Yes. AS7 CONDUCTIVE double braided polyester thermoplastic hose is specified and intended for use with solvents, paints and isocyanates and is rated for an operating temperature range of â40Â°C to +100Â°C. Key points supporting safe use: - Chemical compatibility: The hose description explicitly lists solvents, paints, isocyanates and polyols among the intended fluids. - Construction: A polyamide inner layer provides good chemical resistance; a double polyester braid with conductive fibers (R < 3 Ã 10^4 Î©/m) gives reinforcement and antistatic protection; microperforated polyurethane outer layer adds abrasion and weather resistance. - Standards: Compliance with ISO 8031, SAE 100R7, EN855-R7 and ISO 3949-R7 indicates it meets relevant performance and safety requirements for thermoplastic hoses in fluid transfer applications. - Temperature rating: The stated operating range is â40Â°C to +100Â°C (note a specific limitation: for water and air the upper limit is +70Â°C). Recommendations: Verify compatibility with specific isocyanate or solvent formulations (manufacturer chemical-resistance data), confirm required antistatic earthing practice for flammable solvents, and ensure application pressures and fittings match the listed standards and hose construction.

Can AS7 CONDUCTIVE double braided polyester thermoplastic hose be safely used for water-based fluids and polyols at temperatures up to +70Â°C?

Yes. AS7 CONDUCTIVE double braided polyester thermoplastic hose is suitable for water-based fluids and polyols up to +70Â°C. The hose is specified for solvents, paints, isocyanates, polyols and water-based fluids; its operating temperature range is -40Â°C to +100Â°C, with a specific note that for water and air the limit is +70Â°C. Construction (polyamide inner layer, double polyester braid with conductive fibers, microperforated polyurethane outer) supports use within these limits.

Does AS7 CONDUCTIVE double braided polyester thermoplastic hose provide sufficient antistatic protection for solvent-based paints?

Yes. AS7 CONDUCTIVE double braided polyester thermoplastic hose provides effective antistatic protection for solvent-based paints when used and maintained according to its specifications and application standards. Why: - The hose has conductive fibers embedded in the double polyester braid with a resistance rating R < 3 Ã 10^4 Î©/m, which falls within typical antistatic/earthing ranges suitable for preventing charge accumulation and spark risk in solvent-based paint transfer. - It is explicitly designed for solvents and paints, and constructed to relevant industry standards (ISO 8031, SAE 100R7, EN855-R7, ISO 3949-R7), indicating suitability for fluid transfer applications where safety and electrical dissipation are required. - Construction details support safe use: polyamide inner layer for chemical compatibility, conductive-reinforced braid for mechanical strength and conductivity, and a durable polyurethane outer layer. Operating temperature range (â40Â°C to +100Â°C; up to +70Â°C for water/air) covers typical paint-handling environments. Important caveats: - Antistatic performance depends on correct grounding/earthing of the hose and connected equipment. The conductive braid must be electrically continuous and properly bonded to a ground. - Surface resistance specified per meter indicates good dissipation, but you should confirm whole-system resistance and verify with an ohmmeter after installation and periodically during use. - Compatibility with specific solvent formulations, pressure, and temperature conditions should be verified against the hoseâs chemical and temperature limits. - Microperforated polyurethane outer layer may affect certain environmentsâinspect for wear, contamination, or damage that could compromise conductivity. Recommendation: Use AS7 CONDUCTIVE hose with proper grounding and routine electrical/visual checks; if your application requires a stricter maximum resistance or certifiable antistatic classification, validate with the hose supplier or test to your safety standard.

Flexible thermoplastique à double tresse polyester AS7 CONDUCTIVE

Flexibles thermoplastiques, Tous les produits/

Informations complémentaires

Matériau	PA – polyamide
Température maximale de service [°C]	100
Température de service minimale [°C]	-40
Résistance au vide	vérifier

Flexible léger et souple avec fibres conductrices dans la tresse (R 4 Ω/m), conçu pour les solvants, les peintures, l’isocyanate, le polyol et les fluides à base d’eau. Normes : ISO 8031, SAE 100R7, EN855-R7, ISO 3949-R7. Couche intérieure : polyamide. Renfort : double tresse polyester avec fibres conductrices. Couche extérieure : polyuréthane microperforé. Température de service : de -40°C à +100°C (pour l’eau et l’air jusqu’à +70°C).

Liste des variantes de produit

Référence article	Nom de la variante du produit	DN	BAR	Disponibilité	Actions
ZC-AS7-05	Tuyau thermoplastique AS7 (SAE 100 R7) 3/16"	5	250	En stock	Demande
ZC-AS7-06	Tuyau thermoplastique AS7 (SAE 100 R7) 1/4"	6	228	En stock	Demande
ZC-AS7-08	Tuyau thermoplastique AS7 (SAE 100 R7) 5/16"	8	190	En stock	Demande
ZC-AS7-10	Tuyau thermoplastique AS7 (SAE 100 R7) 3/8"	10	228	En stock	Demande
ZC-AS7-13	Tuyau thermoplastique AS7 (SAE 100 R7) 1/2"	12	140	En stock	Demande
ZC-AS7-16	Tuyau thermoplastique AS7 (SAE 100 R7) 5/8"	16	105	En stock	Demande
ZC-AS7-19	Tuyau thermoplastique AS7 (SAE 100 R7) 3/4"	20	90	En stock	Demande
ZC-AS7-25	Tuyau thermoplastique AS7 (SAE 100 R7) 1"	25	70	En stock	Demande

Vous avez besoin d'une plus grande quantité de produits ou d'un devis personnalisé ?

Appelez-nous : +33 679 352 568 ou envoyez-nous un e-mail : wirthjeanpierre@aol.fr

Envoyer une demande

Flexible léger et souple avec fibres conductrices dans la tresse (R 4 Ω/m), conçu pour les solvants, les peintures, l’isocyanate, le polyol et les fluides à base d’eau. Normes : ISO 8031, SAE 100R7, EN855-R7, ISO 3949-R7. Couche intérieure : polyamide. Renfort : double tresse polyester avec fibres conductrices. Couche extérieure : polyuréthane microperforé. Température de service : de -40°C à +100°C (pour l’eau et l’air jusqu’à +70°C).