Can CETOP bracket for pneumatic actuator flange B, model GL support both clockwise and counterclockwise swivel mounting with the included 4 screws and washers?

Yes . the CETOP bracket for pneumatic actuator flange B, model GL supports both clockwise and counterclockwise swivel mounting using the included 4 screws and washers. The bracketâs swivel flange (cast aluminum) plus the 4 galvanized carbon steel screws and washers are provided to secure the actuator in either rotational orientation, so you can mount the actuator to swivel in either direction without needing additional fasteners. Ensure screws are tightened to the manufacturerâs recommended torque and verify alignment for smooth swivel operation.

Can CETOP bracket for pneumatic actuator flange B, model GL be mounted on different surface materials using the included 4 screws and washers?

Yes - the CETOP bracket for pneumatic actuator flange B, model GL Format can be mounted to different surface materials using the included 4 screws and washers, provided the mounting surface and screw engagement meet basic mechanical requirements. The flange is cast aluminum and the fasteners are galvanized carbon steel; this combination suits common substrates (steel, aluminum, wood, plastics) if you ensure: correct hole alignment, adequate thread engagement or use of inserts for soft materials, sufficient substrate thickness to carry the load, and corrosion compatibility for the installation environment. For high loads, vibration, or corrosive conditions, use appropriate anchors, thread inserts, longer or graded fasteners, or consult an engineer.

Can CETOP bracket for pneumatic actuator flange B, model GL resist corrosion in outdoor environments with the included galvanized screws and washers?

Partially, but with limitations. CETOP bracket for pneumatic actuator flange B, model GL uses a cast aluminum flange and galvanized carbon steel screws and washers. Cast aluminum offers good natural corrosion resistance outdoorsâforming a protective oxide layer that withstands weathering and most atmospheric conditions. Galvanized carbon steel fasteners provide sacrificial zinc coating that protects against rust for a time, making them suitable for general outdoor use. However, long-term corrosion resistance depends on exposure severity: - Mild environments (urban, suburban, occasional rain): the materials should perform well for extended periods. - Marine or highly corrosive environments (salt spray, constant humidity, chemical exposure): galvanized coatings can rapidly degrade; aluminum may suffer pitting or galvanic corrosion where it contacts steel if the zinc coating becomes compromised. - Constant wetting/drying cycles, pooling water, or abrasive contamination accelerate deterioration. Recommendations to improve durability: - For coastal or aggressive environments, use stainless steel fasteners (A2/A4) or apply additional protective coatings. - Ensure proper drainage and avoid trapping moisture between flange and mating surfaces. - Regular inspection and maintenance (re-tighten, replace corroded screws) will extend service life. Conclusion: CETOP bracket for pneumatic actuator flange B, model GL is suitable for general outdoor use with galvanized screws/washers, but for marine or very aggressive environments, upgrade fasteners or apply extra protection to ensure long-term corrosion resistance.

Support CETOP pour bride de vérin pneumatique B, modèle GL

Actionneurs pneumatiques, Tous les produits/

Informations complémentaires

Matériau	AL – aluminium
Longueur standard [m]	10, 2

Support CETOP pour montage avec bride oscillante. Fourniture : 4 vis avec rondelles. Matériau : aluminium moulé (bride), acier au carbone galvanisé (vis et rondelles).

Liste des variantes de produit

Référence article	Nom de la variante du produit	DN	BAR	Disponibilité	Actions
MW-W0950322008	Support MOD.GL-032	-	-	En stock	Demande
MW-W0950402008	Support mod. GL-040	-	-	En stock	Demande
MW-W0950502008	Support MOD.GL-050	-	-	En stock	Demande
MW-W0950632008	Support MOD.GL-063	-	-	En stock	Demande
MW-W0950802008	Support MOD.GL-080	-	-	En stock	Demande
MW-W0951002008	Support MOD.GL-100	-	-	En stock	Demande
MW-W0951252008	Support MOD.GL-125	-	-	En stock	Demande

Vous avez besoin d'une plus grande quantité de produits ou d'un devis personnalisé ?

Appelez-nous : +33 679 352 568 ou envoyez-nous un e-mail : wirthjeanpierre@aol.fr

Envoyer une demande

Support CETOP pour montage avec bride oscillante. Fourniture : 4 vis avec rondelles. Matériau : aluminium moulé (bride), acier au carbone galvanisé (vis et rondelles).