Is the Lightweight foam and spray gun with flat nozzle, polyamide, AKBO suitable for continuous use at 3.5â4 bar without overheating?

Lightweight foam and spray gun with flat nozzle, polyamide, AKBO is specified for low-pressure use with best effect at 3.5â4 bar and a maximum working pressure of 12 bar. MateriaÅy (PA66, stainless steel parts, EPDM seals) oraz temperatura robocza do +50Â°C wskazujÄ na dobrÄ wytrzymaÅoÅÄ mechanicznÄ i odpornoÅÄ chemicznÄ. Jednak opis nie podaje wyraÅºnie dopuszczenia do ciÄgÅej pracy (continuous duty) ani danych o nagrzewaniu przy dÅugotrwaÅym uÅ¼ytkowaniu w zakresie 3.5â4 bar. W praktyce: stosowanie w zalecanym zakresie 3.5â4 bar jest zgodne ze specyfikacjÄ roboczÄ i nie powinno powodowaÄ przekroczenia ciÅnienia roboczego, ale moÅ¼liwoÅÄ przegrzewania zaleÅ¼y od warunkÃ³w pracy (czas ciÄgÅej pracy, rodzaj rozpylanego medium, temperatura otoczenia, czÄstotliwoÅÄ cykli, wentylacja). JeÅli planujesz dÅugotrwaÅe, ciÄgÅe uÅ¼ycie, zalecane jest skonsultowaÄ siÄ z producentem AKBO lub przeprowadziÄ test w warunkach roboczych; rozwaÅ¼ teÅ¼ przerwy robocze i monitorowanie temperatury urzÄdzenia, by uniknÄÄ przegrzania elementÃ³w z tworzyw i uszczelek.

Can Lightweight foam and spray gun with flat nozzle, polyamide, AKBO be used with solvents or aggressive chemicals without damaging EPDM seals?

No - Lightweight foam and spray gun with flat nozzle, polyamide, AKBO should not be used with aggressive solvents or chemicals that can attack EPDM seals. EPDM is resistant to water, steam, many polar solvents, and some alkalis, but it is vulnerable to many hydrocarbons, ketones, esters, aromatic and chlorinated solvents and strong oxidizers. The gunâs sealing and cover are EPDM; exposure to incompatible chemicals can cause swelling, hardening, loss of elasticity and seal failure. If you must use solvents, verify chemical compatibility with EPDM for the specific solvent and operating temperature (max gun temp +50Â°C) or choose a gun/seals made from a chemically resistant elastomer (e.g., FKM/Viton or PTFE).

Does the Lightweight foam and spray gun with flat nozzle, polyamide, AKBO require specific maintenance to keep the EPDM cover and seals functional?

Yes. The Lightweight foam and spray gun with flat nozzle, polyamide, AKBO requires basic, regular maintenance to keep the blue EPDM cover and EPDM seals functional and to ensure reliable operation: - Regular inspection: Check the EPDM cover and seals visually for cuts, hardening, swelling, or chemical degradation before each use and during periodic inspections. Replace if any damage or loss of elasticity is found. - Cleaning: After each use, flush the gun and nozzle with an appropriate solvent or cleaner compatible with EPDM (avoid strong ketones and oils known to swell or degrade EPDM). Remove foam residues from the cover and surrounding areas to prevent abrasion or trapped chemicals that can degrade the rubber. - Avoid incompatible chemicals: EPDM is resistant to many water-based and alcohol-based cleaners but can be attacked by certain oils, hydrocarbons, and aggressive solvents. Do not expose the EPDM cover and seals to known incompatible substances. - Temperature and pressure limits: Operate within the specified maximum operating temperature (+50Â°C) and working pressure limits (max 12 bar; recommended low-pressure use 2.5â4 bar). Excessive heat or pressure can accelerate seal aging. - Lubrication and parts care: Use lubricants compatible with EPDM when required (silicone-based or manufacturer-recommended lubricants). Stainless steel trigger, spring, and valve stem require minimal corrosion care, but keep them clean and dry to prevent particulate wear that could damage seals. - Storage: Store the Lightweight foam and spray gun with flat nozzle, polyamide, AKBO in a cool, dry place away from direct sunlight, ozone sources, and aggressive chemicals to prolong EPDM life. - Replacement schedule: Even with proper care, replace EPDM seals and the cover periodically as part of preventive maintenance based on usage intensity and inspection findings. Following these steps will help maintain sealing performance and extend the service life of the EPDM components.

Pistolet léger à mousse et pulvérisation avec buse plate, polyamide, AKBO

Informations complémentaires

Pistolet léger à mousse et pulvérisation avec buse plate (buse orientable) à basse pression – 2,5 bar (meilleur effet à 3,5 ÷ 4 bar). Fabriqué en polyamide PA66 renforcé de fibre de verre. Matière : polyamide PA66. Gâchette, ressort et tige de vanne en acier inoxydable. Capot en caoutchouc EPDM bleu. Étanchéité : EPDM. Connexion (entrée) : filetage femelle 1/2″ BSP. Pression de service maximale : 12 bar. Température de service maximale : +50°C.

Liste des variantes de produit

Référence article	Nom de la variante du produit	DN	BAR	Disponibilité	Prix	Quantité	Actions	Catalogue
AK-NLFW2	Pistolet léger pour lances et buses AKBO, (entrée) filetage femelle 1/2" BSP, (sortie) buse plate, PA66, bleu	-	12	En stock	0 zł		Demande

Vous avez besoin d'une plus grande quantité de produits ou d'un devis personnalisé ?

Appelez-nous : +33 679 352 568 ou envoyez-nous un e-mail : wirthjeanpierre@aol.fr

Envoyer une demande

Pistolet léger à mousse et pulvérisation avec buse plate (buse orientable) à basse pression – 2,5 bar (meilleur effet à 3,5 ÷ 4 bar). Fabriqué en polyamide PA66 renforcé de fibre de verre. Matière : polyamide PA66. Gâchette, ressort et tige de vanne en acier inoxydable. Capot en caoutchouc EPDM bleu. Étanchéité : EPDM. Connexion (entrée) : filetage femelle 1/2″ BSP. Pression de service maximale : 12 bar. Température de service maximale : +50°C.