Is the Two-part hose clamp with catches, US version, cast iron suitable for hoses operating up to 25 bar when installed with compatible fittings and hoses?

Yes. The Two-part hose clamp with catches, US version, cast iron is suitable for hoses operating up to 25 bar when used with compatible fittings and hoses and installed correctly. The product description states it is made of high-quality galvanized ductile cast iron with a locking mechanism for hose mounting and explicitly notes that with proper installation, appropriately selected hose, and fitting, a working pressure up to 25 bar is achievable. Ensure you verify the hose and fittingsâ pressure ratings, follow manufacturer installation instructions, and perform pressure testing as required for your application.

Does the Two-part hose clamp with catches, US version, cast iron resist corrosion after yellow passivation without hexavalent chromium?

Two-part hose clamp with catches, US version, cast iron Format: Yes - the product description indicates corrosion resistance. The clamp is made of galvanized ductile cast iron with yellow passivation explicitly free of hexavalent chromium. Galvanization plus a yellow (trivalent/hexavalentâchromiumâfree) passivation layer provides improved protection against rust compared with bare iron. However, longâterm performance depends on service conditions (humidity, salt exposure, mechanical damage to coating) and correct installation. With proper installation, suitable hose and fitting, and typical environments, the clamp will resist corrosion; in highly aggressive or marine environments additional protection or stainless alternatives may be advisable.

Can the Two-part hose clamp with catches, US version, cast iron be used for high-vibration applications without loosening?

The Two-part hose clamp with catches, US version, cast iron can be suitable for high-vibration applications, but only under certain conditions. Why it can work: - Construction: made of high-quality galvanized ductile cast iron, the clamp is robust and resistant to fatigue compared with brittle cast materials. - Locking mechanism: the connection to the hose part includes a locking mechanism (catches/hooks) that provides positive engagement and helps resist loosening from cyclic loads. - Pressure rating: when properly installed with a correctly matched hose and fitting, it is rated for working pressures up to 25 bar, indicating a secure seal under load. Limitations and required precautions: - Vibration resistance depends heavily on correct installation: ensure the clamp is properly seated, catches fully engaged, and torque/fit is per manufacturer guidance. - Hose and fitting choice is critical: use hoses and fittings designed for high-vibration service (compatible diameter, reinforcement, and sufficient stiffness). A soft or undersized hose can allow relative movement and promote loosening. - Supplementary measures: consider using anti-vibration mounts, safety wires, secondary clamps, or thread-locking/locking devices on adjacent fittings if vibration is severe. - Periodic inspection: in high-vibration environments, regular checks for deformation, wear, or loosening are recommended. Conclusion: The Two-part hose clamp with catches, US version, cast iron can be used in high-vibration applications without loosening if correctly selected and installed with compatible hose and fitting, and if additional vibration-mitigating measures and inspections are applied.

Collier de serrage pour flexible en deux parties avec crochets, version US, fonte

Informations complémentaires

Matériau	CS – acier (fonte)

Collier en deux parties, version USA, avec crochets (« griffes »), en fonte ductile galvanisée de haute qualité (passivation jaune sans chrome hexavalent). Conçu pour le montage de flexibles, avec connexion à la partie flexible dotée d’un mécanisme de verrouillage. Matériau : fonte ductile galvanisée. Avec une installation correcte, flexible et raccord appropriés, pression de service jusqu’à 25 bar.

Liste des variantes de produit

Référence article	Nom de la variante du produit	DN	BAR	Disponibilité	Actions
LU-LB-10	Collier de serrage en fonte, 2 pièces, type US, pour tuyau de 19 mm, plage 38 à 43 mm	-	-	En stock	Demande
LU-LB-4	Collier en fonte 2 pièces, type US, pour tuyau de 13 mm, plage 21÷27 mm	-	-	En stock	Demande
LU-LB-9	Collier en fonte 2 pièces, type US, pour tuyau de 19 mm, plage 33÷38 mm	-	-	En stock	Demande
LU-LBU-29	Collier en fonte en 2 pièces, type US, pour tuyau de 50 mm, plage 63 à 70 mm	-	-	En stock	Demande
LU-LBU-9	Collier en fonte en 2 pièces, type US, pour tuyau de 19 mm, plage 30÷33 mm	-	-	En stock	Demande
LU-SKA-10	Collier en fonte 2 pièces, type US, pour tuyau de 25 mm, plage 34 à 45 mm	-	-	En stock	Demande
LU-SKA-34	Collier en fonte en 2 pièces, type US, pour tuyau de 19 mm, plage 30 à 35 mm	-	-	En stock	Demande

Vous avez besoin d'une plus grande quantité de produits ou d'un devis personnalisé ?

Appelez-nous : +33 679 352 568 ou envoyez-nous un e-mail : wirthjeanpierre@aol.fr

Envoyer une demande

Collier en deux parties, version USA, avec crochets (« griffes »), en fonte ductile galvanisée de haute qualité (passivation jaune sans chrome hexavalent). Conçu pour le montage de flexibles, avec connexion à la partie flexible dotée d’un mécanisme de verrouillage. Matériau : fonte ductile galvanisée. Avec une installation correcte, flexible et raccord appropriés, pression de service jusqu’à 25 bar.